How to protect injection molding machine-Dakumar injection machine

Injection molding machine is one of commonly used equipment in the plastic processing industry,it is usually long hours,so how to guarantee the stability of injection machine in continuous production of normal work,no matter for injection machine manufacturer or user is a worthy of attention and efforts to solve the problem.

the ideal working temperature of hydraulic system should between 45 ℃ to 50 ℃,should pay attention to daily check for leaks,replace worn seals,as early as possible to tighten loose coupling, etc.After repair to check the amount of oil,gas supply in time.To use the appropriate hydraulic oil, and periodically check the hydraulic oil oxidation degree (to judge from the color of deep),more than a certain number of work hours after explorers oil is absolutely necessary.Oil filter should be cleaned once every three months,check oil screen damage at the same time,the cooler should be cleaned once a year,or on the basis of their ability to work ever reduce,cleaning,cooling water should choose soft (no minerals) is preferred.

Electrical parts,need to regularly check the terminal position and tighten,motor each year for regular cleaning.Heating tube of burnt down in the normal production is less visible,to pay attention to the working condition of temperature controller for this purpose.The contactor used for electric parts,if found contact with overheating,noise or breaking of fire is very big,has said the damage,should be replaced as soon as possible.And should be timely check the outside disturbance to the computer control part.

Mechanical parts,template parallelism can reflect the status of the clamping part,most template parallelism adjustment shall be controlled by professional personnel according to the working steps,or adjust the improper damage to the machine.Regularly use mould thickness adjustment system,use the same mold production machine for a long time,the inspection must be conducted to avoid failure.For the central lubrication system, even daily bearing injection system check,maintain the smooth action.

Written by Tina

Dakumar machinery company

Mail:dakumar-serve@dakumar.com 

Whatsapp:008615167663781

How to make a high quality plastic injection mould-Sino mould

Quality of the mould,it will directly affect the product quality, yield, cost,production of new products and old products renewal cycle,product structure adjustment speed and market competitiveness,therefore,the economic situation puts forward higher and higher requirements about the quality of the mould.

There are four aspets control mould quality:

1.product quality:product size stability, compliance,roughness on the surface of the products, products material utilization ratio and so on;
2. the service life:on the premise of ensure the quality of the products,the mould can be done by a number of fabrication or production cycles.
3. the use mould maintenance: whether to belong to the most convenient to use,easy mold release, production of auxiliary time as short as possible;
4. the maintenance cost,periodic maintenance and so on.

Mould design is reasonable,the die structure design,compact structure,easy to operate.As far as possible to reduce the maintenance one parts need to tear open outfit.The selection of die materials,both to meet customer requirements for product quality,to surface strengthening of main forming parts,mold correct use and maintenance,is also a big factor to improve the quality of the mould.

Written by Tina

Mail:serve@sinomould.com

Professional PET preform mould maker-Sino mould

Sino mould is a professional manufacturer of PET preform mould,PET bottle preform,Many years committed to preform mouls,test tube mould,bottle cap mould research and manufacturing,rely on constant innovation and improve,have enjoyed a high reputation.

We are specialized in the production of needle valve mould, do not need artificial cut gate.The use of advanced hot runnersystem, guarantee the products AA values at a low level.Reasonable cooling channel design,strengthened the mould cooling effect,effectively shorten the molding cycle.

Secone the choice of materials:
1. The major parts of the mould material chooses import S136 (Sweden - wins best).
2. Mold base material,USES the import P20 material,electroplating processing, improve the corrosion resistance of mold,prolong the service life of the mold.
3. Heat treatment of parts,using the German import vacuum furnace processing,parts hardness assurance in HRC45 ° - 48 °
Professional after-sales service engineering and technical personnel, good brand reputation, guarantee the stability of mould machine running.

If you interested our cooperation,welcome to join us,we will do our best satisfy your specific request and good profit reward.Mail:serve@sinomould.com

Plastic bumper mould professional mould manufacture

SINO MOULD is a professional auto bumpermould manufacturer with many years' experience,we have developed fast and strict control for the mould size and quality,as because we realize the customers' demand and do improvement on our bumper mould.

Our factory has a complete set of advanced mold processing equipment,including CNC machining centers, mold clamping machine,high speed milling,deep hole drilling, CNC edm machine,CNC wire cutting machine and other processing equipment more than 90 sets.First-class CAD/CAE/CAM system,a team of professional theoretical knowledge and experienced technology backbone team,the perfect combination of both,formed Sino mold design research and development of a strong core.

Bumper injection material:PP+EPDM+T20

bumper dimension:1670*690*561 mm
Bumper injection cycle time: 45s

6 points valve gate type nozzle can obtain the best performance of the bumper.

we are specialized in valve gate bumper mould for more than 20years ,if you have this kind of project or you are on the same field.please feel free to email me

Mail:serve@sinomould.com

Whatsapp:008615167663781

Using standard mold componets

Standard mold part are president in most modern molds.A whole mold making industry has been created which manufactures and supplies standard mold components based on a catalogue selection and order syste,.Faster delivery and financially competitive are ones of the major attractions to the mold maker.It is also an important factor if the mold has break down and it is required for production.

The advantage of using standard mold components include:

1.       shorter mold construction lead time.

2.       Increased machining capacity in house.

3.       Ease of mold maintenance

4.       Reduce mold downtime

5.       Reduce the overall long-tem costs.

The main disadvantage concerned with the use of standard mold components tends to be associated with the following:

1.       Reliance upon one specific source of supply

2.       Failure to supply on time.It is a rare occurrence with most suppliers,but it should be considered the delivery time quoted by supplier and place order on time.

3.       Mistakes in part ordering caused longer mold downtime.

Standard parts system is divided into two general groups

1.       standard mold base system

2.       Accessory components,like ejection,slide,cooling and so on.

Written by Tina

Mail:serve@sinomould.com

Injection molding line cooperation with Sino group

Sino holdings group constant innovation and upgrade our technology,Based on injection molding machine,Our group develop to produce high quality plastic injection moulds for various product,and each steps production auxiliary molding machine,we provide professional technical skill support,avalibale to send after-sales service engineer provide technical support,engineer training and maintenance.

In 2016,Sino holdings group will complete big type injection molding machine with 3000Ton and 4000T machine.These kind of machine will put into big production,and suitable for produce big size plastic injection mould,such as table,auto bumper,pallet,door and so on.

SINO is a leading brand in injection mould industry which supports good quality and diamond service to customer.We are very happy we will have this chance work with you.

Our rich experience will help you save much time and cost.We can help you provide a whole complete working line from a sample to a whole sets plastic molding line.

Welcome to join our team and grow with Sino group,develop new project.

Written by Tina

Mail:serve@sinomould.com
     dakumar-serve@dakumar.com
whatsapp:008615167663781

Plastic table mould maker-SINO MOULD

Sino mould professional in various plastic table mould,Round mold,square mould,mold, rectangular table mould. Mould processing, we provide solutions for deformation of rectangular table mould.We are professional for those who have legs and have a special table mould design,design a more small size injection molding machine,and automatic ejection.Below is the table mould detail mould information which we made before:

Mould Feature:

·         Mould Name :plastic table mould

·         Mould Cavity: 1 cavities

·         Injection Units: Hot runner gate injection

·         Table size:830*830*500mm

·         Mould Size: 1310mm*1190mm*690mm

·         Mould core and cavity material:P20

·         Mould Life: 2 million shots

·         Ejection :fully automatic drop

·         Cycle time:70-80s

Sino moulds pecialize in the plastic injection mould design and manufacture,and the table mould we made cover complete spefication.Sino mould owns more than 20 years mould develop and design experience,adopt the newest design innovation concept. With high quality process, there is the premise of quality assurance, won the trust and support of users.  

Sino mould accept various and customized table mould order,If you have any moulds confusion,please do not hesitate to contact Tina.Tina will introduce our mould well and best service for you.Mail:serve@sinomould.com ,skype:anole-01

How to finalize the cable tie mould quality?

Sino mould rich experience in the plastic nylon cable tie mould manufacture,also good at distinguish the good cable tie mould.Today let us help you clear how to judge a good cable tie and good quality cable tie mould.

l   the appearance of the cable tie inspection

Qualified cable tie appearance usually don't have plastic products is easy to appear the burrs (caused by clamping not tight), lack of material (parts), black spots (mixed with mixed material), flow mark, anxious (poor high mold temperature exhaust), yellow (injection when the temperature is too high, cooling is not timely), the residual tooth (mold is broken cause), etc., unqualified products are filtering through quality control in production workshop.

l   Size inspection

The rib size of the cable tie and precision directly affects the normal use of cable tie and load-bearing capacity.

l   Quality inspection

With quality to sum up depends on the production of precision manufacturing cable tie mold technology, the quality of raw materials used, the supervision of the quality monitoring, the reliability of the injection molding machinery and equipment and other factors.

In former,one of our customer request the cable tie can self-lock and hold 110kgs,holding for more than 1 hour to reach the experiment standard,we successed.

If you have any confusion of the plastic cable tie mould manufacture or you have this mould enquiry,welcome to Sino.Tina warmly welcome to work with you.and rich experience for the cable tie mould  handle.

Contact:serve@sinomould.com

Skype:anole-01

Whatsapp:008615167663781

Plastic cable tie mould-Sino mould

Sino mould professional in making differet shape and size cable tie mould,owns professional quality inspection personnel,to strictly control the procurement of raw materials,products strict inspection,to ensure that the cable tie products excellent quality low for every customer,every batch of products are set up archives,and attached inspection report, to make quality well documented.

Here is the cable tie mould we made before:

Mould Feature

Mould Name : cable tie 100*2.5mm

Mould Cavity: 32 cavities

Injection Units: cold runner

Mould Size: 450 x 400 x 350 mm

Cycle Time: 15s/stroke,if machine better,can reach to 10-12s/shot

Mould Life: 1 million shots

Mould Core & Cavity: use DIN1.2344

Ejection :fully automatic drop

Mainly produces self-locking type (pine,signs,color) nylon cable tie,PET no core cable tie,core cable tie, gold and silver tie cabletie mold series.Compared with peers,performance excellence,quality are far ahead of all products have to pass strict quality inspection,100% perfect quality to ensure that products

Welcome to make detail enquiry,if you have any demand for plastic cable tie.

Contact Tina

Mail:serve@sinomould.com 

Skype:anole-01

Whatsapp:008615167663781

Professional pipe fitting mould manufacture-SINOMOULD

Sino mould the most experience pipe fitting mould supplier,we did more than 2000sets pipe fitting moulds last year,and good at mould mold flow analysis,help you solve confusion before start make the moulds.As a professional pipe fitting mould manufacturer,we are interested in the mould structure development and innovation of pipe fittings mold manufacturing for many years,to provide you with high precision pipe fitting mould.

Mould Feature:

· Mould Name :Pipe fitting mould

· Mould Cavity: 4 cavities

· Injection Units: cold runner

· Mould Size: 600*600*450mm

· Cycle Time: 45s/stroke,if machine better,can reach to 40s/shot

· Mould Life: 5 million shots

· Mould Core & Cavity: use Thyssen Krup DIN 1.2316 or Stavax S42

Cavity core quench hardening steel is expected, and keep the cavity core hardness between HRC46-50.

· Ejection :fully automatic drop

With Standard parts and assembly parts in stock and strict quality control on the stock parts harden and size guarantee.And some special accessory parts,we will have moderate stock,Such as the core, the hydraulic oil cylinder,etc.

Sino pipe fitting mould,with products processing and the perfect set of vertical integration of operational processes,more to ensure tube mould quality and the reasonable operation costs,make it more in the market competition force.

Contact Tina

serve@sinomould.com

19L bottle cap mould-SINOMOULD

Sino mould professional in 16,24,32cavities 5 gallon cap mould.Sino mould owns more than twenty years of 5 gallon cap mould research and production experience.Is the professional 5 gallon mould design and manufacture.Adopt advanced system technology,decrease the mould production time and improved the mould quality.
 Mould Feature:
•Mould Name:5 gallon cap mould
•Mould Cavity:16 cavities
•Injection Units:16 Points Anole Hot Runner with German heating elements
•Mould Size:496*446*480mm
•Cycle Time:20s/stroke,if machine better,can reach to 15s/shot
•Mould Life:5 million shots
•Mould Core & Cavity:S136
•Mould Base:P20
•Ejection:fully automatic drop
                   

Sino mould committed to a set of production line research and development, production,assembly and packaging services.Sino plastic mould co.,LTD., specializing in the production of:plastic mold,household appliances mould, automobile and motorcycle accessories mould,commodity mould,fitness equipment mould,etc.
Tina Contact: serve@sinomould.com

Plastic injection crate mould-Sino mould

Sino mould is the world leading crate mould manufacture,we have design and produce more than 2000 different kinds of turnover box mould.Such as bottle crate mould,aquatic class turnover box mold,melon and fruits,vegetables container mould,bread caked food grade box mould and etc.In particalar,we also made 2 cavities and 4 cavities crate mould and a superposition of four cavity molds.Sino mould is the First mould company who made superposition box mould in China.This kind of crate mould suit for high speed injection molding and the cycle time only need 42 seonds.So to say,sino mould is the world leading crate mould manufacture.

1. How to make the crate mould using life longer? First for mold base and mmouldcore cavity part,the steel material should choose right.For example: the production of a pair of a four cavity turnover box mold,must use the hardness higher than 33 pre hardened steel formwork,and then select the appropriate harden mould standard parts. Second, must control the hardness of each piece of steel material, can't be too hard. Then, turnover box mold friction and guiding parts must be processed, cannot use any manual work. Finally, some mould company may use cycle material for injection molding, at this moment we have to consider the following two points: A. How to ensure that the tiny impurity damage in the plastic core,cavity; B.how to prevent impurities into the cavity.

 Written by Sino mould-Tina
Mail:serve@sinomould.com

Injection mould decoration (IMR) process-Sino mould

As the world economy level of development,the industrial design requirements more and more attention to fashion,environmental protection,lightweight design,IMR technology emerged,has been widely applied in all walks of life,from the earliest consumer products such as notebook shell,mobile phone lenses,household appliances all kinds of decorative panels,car dashboard,car inner decoration,medical instrument panel,cosmetics boxes,children's toys and so on.

What is the IMR?

IMR (In-Mould Decoration by Roller):Chinese model inside decoration,is the decorative pattern and functional pattern through high precision printing machine printing on foil membrane (film),through high precision to foil device will foil into the special toolings for precise positioning,through the injection plastic raw material of the high temperature and high pressure.The foil pattern on the membranes of the transfer to the surface of the plastic products,is a kind of decorative pattern and plastic molding technology can be implemented.

The principle of IMR
Design printed on a layer of foil membrane,through the diaphragm and plastic model cavity of film laminating for injection molding,injection molding of pattern after the ink layer and foil membrane separation,ink layer on the plastic parts for surface decorative figure.

Written by sino mould Tina
Mail:serve@sinomould.com

Transparent products injection common problems in the process of formation and countermeasures

Transparent products products relative to other luster, there will be particularly obvious if appear surface appearance problem.In the process of the injection molding bad ratio is relatively high.


Common trouble spots are air bubble,weld line and black spots.
The following simple parsing the reasons and countermeasures.
1,bubbles,porosity may cause:melt temperature is too high, lead to materials decomposition;Low injection pressure,mold temperature,holding time short lead to bad materials for the products;Insufficient material drying, impurities in molten material inside the foreign body.Improvement countermeasures:appropriate reduce melting temperature,improve the injection pressure,mold temperature and the holding time.Material is fully dry.

2,welding scar, possible reasons:low melting temperature,mold temperature, injection pressure,the holding time is insufficient,lead to poor liquidity in the molten material in the cavity;Mold venting is not good;Design of gate location is not reasonable to improve countermeasures:to provide the molten material,mold temperature,injection pressure increased time,is the rapid filling material.Increase exhaust slot,redesigned into glue.

3,black spots may cause: materials of impurities;Melt temperature Settings,which leads to the materials decomposition;Gun barrel and stagnation expected nozzle segment.
To improve countermeasures: material thoroughly remove replacement, melting temperature appropriate adjustments,cleaning gun barrel and the nozzle.

Sino mould profeesional in various moulds production and best in the plastic molding problem solution.Sino mould also offer plastic products production service.If you have any project,please feel free to contact serve@sinomould.com

Automotive plastic parts material general request summary -Sino mould

Sino automotive mould company most making the plastic auto parts mould.like the Exterior Trim Parts Mould,Interior Parts Mould,Air Ventilator Plastic Injection Mould,Lighting System Mould,Cooling System Mould,Blow Plastic Parts,Punching / Die-casting Moulds.As per some customer request,they prefer make high strength and good appearance sample first,to choose a suitable plastic material.

1.The impact strength and modulus of equilibrium (at the same time, having the features of strong and tough
Good dimensional stability,namely material creep resistance under load for a long time is better);
2.Good temperature resistance,guarantee the material under the condition of light and heat deformation;
3.Have specific surface properties,such as matte,high hardness,scratch resistance,easy to coating,electroplating,etc.;
4.Excellent weatherability,guarantee the long time use,not aging crack (including hot oxygen aging and the aging);
5. Good resistance to chemicals,in order to resist the erosion of oil products and chemical products;
6.Easy molding,injection grade material should have sufficient liquidity, to ensure that the complex components of forming,and improve productivity;
7.Economy and asked for materials with high cost performance.

Sino auto mould also have many experience in making auotomotive molding and is a famous automotive mould company China.Welcome to contact with SINO,we are sure you will be satisfied with our plastic mould,molding solution and service.
contact mail: serve@sinomould.com

The standard for the injection machine and machine robots connection-Dakumar injection machine

Injection molding machine and the interface of the manipulator is a handshake protocol,coordinate the order of the injection molding machine and manipulator.Interface defines the machinery installation and electrical agreement,the current domestic use more generally accepted standard is the European standard 12, European standard 67,domestic there are a lot of injection molding machine manufacturers,but with the manipulator interface of various electric agreement.At present most of the injection molding machine equipped with 32 core interface.

Many domestic injection molding machine manipulator interface signals usually only a few manufacturers,as shown in the following:

Injection molding machine manipulator to signal:stop,exit,mould and finished, automatic state.
Robots for injection molding machine:signal interlock,allowed out,take out.

Interface is injection molding machine and manipulator of language communication, injection molding machine manufacturers,manipulator manufacturers, if a user can follow to follow this kind of language,so can bring convenient to each other.

Dakumar injection molding machine company is the professional moulds,Injection machine and robots manufacture,we can offer you turnkey project solution on-stop solution.
Contact: dakumar-serve@dakumar.com   

Touble color cup/coffee cup plastic injection solution mould manufacture

plastic caps mould with 12 cavities automatic mould production

PET Preform packing mould|plastic bottle prefrom mould manufacture-Sinomould

Over more than 20 years Sino mould has been committed to PET bottle,bottle, plastic bottle cap mould research and manufacturing,rely on constant innovation and improve,employment and enjoys a high reputation.The company as the leading enterprise in bottle preform mould technology,with Germany,Japan and other advanced processing technology,focus on the international mold manufacturing standards,high quality, high efficiency every detail in the completion of the injection mold making,has been set up and perfect a set of suitable for bottle preform mould research and development,production,sales and service management system,brought together a group of outstanding design,production, processing personnel,we believe that good management and the extraction of talent is a top-class products.

We are specialized in the production of needle valve mould,do not need artificial cut gate.The use of advanced hot runner system,guarantee the products AA values at a low level.Reasonable cooling channel design,strengthened the mould cooling effect,effectively shorten the molding cycle.Adopt original imported Germany Hotset.The control electric box adopts German intelligent temperature controller (PID control uninterruptible power supply).The temperature control box can be custom made according to customer requirements or regulating control electric box.

Professional after-sales service engineering and technical personnel,good brand reputation,guarantee the stability of mould machine running.Avoid cut gate, reduces the labor intensity of workers.let each customer satisfaction.After-sales service provide for you forever until after the completion of the plastic mold life termination.

Tina
Mail:serve@sinomould.com
Skype:anole-01

Plastic cap mould manufacture|flip cap injection mould-Sino mould

Sino mould can provide 1 to 128 cavities bottle cap mould.Manufacturing cap moulds contains:mineral water cover, cover, 5 gallon cover,jelly bottle,shampoo flip.All kinds of oil bottle lid,sports cap,cosmetics, beer cap and barrel cover,and etc.

Usually the cavities for cap mould hot runner system has 6、8、12、16、24、32、48、64、and Sino mould with good hot runner system manufacturers will have the ability to produce cap mould hot runner system with 72、96、128cavities.

Mould feature:

Mould name flip top cap

Mould system:Hot runner

Ejection:automatic flip top close,fully automatic drop

Mould life:10 millon shots

Mould material:starvax S420 for core and cavity,P20 for mould base.

Sino mould specialize in all kinds of plastic bottle cap mould,cosmetics cap mould,plastic mould,plastic bottle cap mould,plastic mould, zinc aluminum alloy mold company, plastic mold;Cosmetics bottle cap mould away, health care products cover mould, auto mould, commodity mould of professional manufacturers.The pursuit of customer satisfaction is our greatest responsibility, the pursuit of excellence perfection, our purpose is to welcome your inquiry at any time.

Sino mould contacts:Tina

Skype:anole-01

Mail: serve@sinomould.com  

Bumper mould manufacture|auto bumper mould-sinomould

Modern car’s front and rear bumpers adopt plastic as raw material, not only can keep the function of protection, but also has with the harmony and unity of the body shape, lightweight, reduce fuel consumption, etc.Sino auto bumper mould 

Bumper plastic choice,must satisfy the several aspects like a good use of performance requirements, process performance requirements and reasonable cost requirements.When choosing modified PP materials, shall meet the following four basic characteristics:
First, good heat resistance, then this range (80-100 ℃)
Second, the impact strength should be controlled in （0.3-4）J*cm²
Third, the scope of the tensile strength by 29 Mpa
Fourth, good formability and weather resistance.

Chinese mould made by sino-Bumper thickness range is generally (3 +) 0.25 mm - (3.5 + 0.25) mm. The design, with enough variation in thickness transition zone to avoid impact parts surface quality of the thickness of the change of purpose.Ejection Angle should be greater than zero.Car front bumper is a safety device, capable of absorbing and buffer the impact to protect the front car body.The bumper is a safe, and decoration, its structure design is closely related to the vehicle safety, not only the vehicle quality perception.

Contact Tina

Mail:serve@sinomould.com

Skype:anole-01

Installation for the mould-plastic injection mould installation steps-sinomould

Customer most less care for the mould installation,that maybe caused some wear for the mould demage.

Today lets share with you a detail steps for the mould installation on plastic injection mould.We are professional in this field,Below is the steps:

1. Mould installation
1) Clean the mould plate locating ring and the mould installation surface dirty parts or flash.
2) Since the mould not very big,we adopt the whole sets installation method.First set two wooden plate at the machine mould installation downside.mould installation at the machine plate,Fixed side mould location ring should be set well.Then close the mould,Use the mould clamp fix the mould on the machine mould plate.Fix the moving side on the machine mould plate.
3) Adjust the mould clamp system,ensure the enough mould open distance and the clamp force,keep suitable mould close state.
4) Slow to open the mould plate until the mould plate stop moving back,adjust the eject device,keep the eject distance.Open mould to check the eject structure moving situation,whether balance or stable.
5) After mould installation,wait the injection machine barrel and nozzle reach to 20-30℃，adjust the nozzle and spure relative place and radius connection situation.Can put a paper between them to check the match situation.
6) Start empty shoot and running,to check whether normal.

Sino mould professional in making various injection mould and for each mould assemble and the installation on injection machine,we are very care and protective.For the mould maintenance,we are rich experience,If you have new enquiry or any problem,welcome here to make detail consultation.

Contact Tina
Mail:serve@sinomould.com
Phone:+8615167663781
Skype:anole-01

Pallet project building exportation|Plastic pallet mould manufacture-sinomould

One-stop plastic injection moulding service detail:Sino holdings group offers turnkey project whole set service.For the pallet project,before make the investment,customer should do a detail and correct market survey for the sales,promotion and material etc field.Since pallet project not a small one,when you plan to make the investment,you should consider detail for all the risk and your reward.Anyway,sino mould will stand with you together,our team will help you analysis all the detail your consider,we will do our best support best suggestion.

Mould description：
Mould name: Plastic pallet mould
Pallet size:1200*1000*150mm
Mould size:1800*1600*1150mm
Plastic material:PE
Number of mold cavity: 1 cavities
Injection form: 20 tio hot runner runner
Cycle time: 200 seconds/cavity
Ejection way: Ejector pin
Mould life: 500K shot
Mould core and cavity material: P20
Machine:DKM2600 servo motor injection machine

Thank you very much willing to trust sino,we will help you build a perfect and reasonable project whole line moulds,machines and factory,also will help engineer training,machine management and project detail distribution.

Written by Tina
Mail:serve@sinomould.com

Wire coiling plastic thread pipe|professional chinese mould maker -sinom...

Clothes washer|Washing machine mould maker-Sino mould

Washing machine mould made in sino.Sino mould mainly engaged in plastic injection mould making, involving areas: commodity mould, washing machine mould,turnover box mold,washing machine mould,household appliances mould (air conditioner mould, washing machine mould,refrigerators mould,air purifier,air conditioner mould etc.), automobile and motorcycle accessories, TV mold.

Mould parameter detail:
Mould cavity: one cavity
Mould production delivery time:65-75days (Generally mould production cycle time,determined by product specific detail.
Mould core and cavity material:P20 or customized.
Mould package:strong wooden box

After confirm the order with customer,customer better send the sample or washing machine 3D drawing for us to make the mould 3D design.We will make the washing machine mould design according to the customer offered information.Then our technical design engineer would provide mould 2D and 3D drawing. After waiting for customer confirmation to arrange production of washing machine mould.

Washing machine mould maintenance items:
1.Mold inside the cavity and core need to clean up after use, can't leave sundry, so as not to damage the mould surface, spraying antirusting agent.
2.Mold cooling system inside of residual water, must be clean, in order to prevent mould rust water blocking.
3.Mold mechanical standard parts shall be coated with lubricating oil, for example: under the guide pin - thimble - reset lever - guide pillar and so on.
4.After mould clamping, with dust cloth cover, should avoid dust into the mold, cause mould rust.

Washing machine mould maker-sino mould will do our best to serve you very well.welcome to sino to know the detail production.
serve@sinomould.com
skype:anole-01

Bucket mould manufacture|Plastic paint bucket supplier-Sinomould

Sino mould paint bucket mould, with products processing and the perfect set of vertical integration of operational process, the mould from the raw material, production, a series of processing services.More to ensure that the paint bucket mould quality and reasonable operation costs.Our company specialized in manufacturing series of different specifications for different types of plastic mold manufacturer.

The main technical points of the paint bucket is eccentricity and ejection system problem, seal water requirements, and drop test.Sino mold in the 15 years has done more than 2000 sets paint bucket mould.We have strong technical force and rich experience on the paint bucket mould design and production.

Sino is a group professional in making plastic molding line solution.If you plan to make a whole bucket production line,Sino can satisfy all your requirement.We are not only a mould company,our branch company Dakumar injection molding machine company support high quality injection molding machine and auxiliary machine for best running system.And the whole line will be strictly track by our most experienced project engineer follow hard and we support oversea market solution.We offered is a turnkey project solution.

Sino mould is a mould maker consist of mould design and manufacture of professional manufacturers,has a skilled and experienced technology backbone team and advanced processing equipment, each leading the paint bucket mould quality,high hardness,good corrosion resistance can, long service life.Offers a variety of models of the paint bucket mould.

Professional plastic turnover box mould

Sino is the leader of the plastic turnover box mould maker in china,we do good research for more than 2000 kinds of crate mould,suchlike the bottle crate mould,fish crate mould,vegetable crate mould,bread cratemould …etc.

Especially,we success in the 4 cavity crate mould production and experience in the crate mould production field,in china,we are the professional.This kind of crate mould can using on DKM high speed injection molding machine.This injection cycle time can realize 42s.Mould size:1660*1200*1200mm,crate size:380*280*150mm.

Sino mould the famous mould maker in the mould manufacture industry.How to make a long life time for the crate mould? Choose suitable steel to make the mould base and mould core,cavity main parts is the most important.If you plan to make 4 cavity crate,the mould base request to use HRC higher than 33.And choose durable steel as the mould antifriction parts.But if deal with steel materials, must be reasonable control the hardness of the steel, should not too high.And mould sliding and guiding position request use precision process.

Some times,customer request using the recycle material to produce the crate,we should do more care with two points: A.How to ensure the tiny iron particles in the plastic and stones will not scratch core and cavity. B.How to prevent small iron grains and stones into the cavity.

Welcome to sino,will offer you best solution and suggestion for the crate mould.

Mail:serve@sinomould.com

Skype:anole-01